使用 VxWorks C 将二进制数据发送到串口

Question

您好，我正在尝试对我的 UEIPAC 600-1G 立方体进行编程以从温度传感器接收数据。为了激活传感器，我必须向它发送二进制数据。我正在尝试发送设置为十六进制值的字符，但出了点问题。我通过将数据转储到文本文件中进行了测试，我得到了空格后跟一些乱码字符。如何通过串口发送二进制数据？

struct timespec tim, tim2;
unsigned char access_code[] ="       ";
int bytes=256; /*num of bytes to read at a time*/
char re[bytes]; 
int re_len = 0;
int n_access = 0;   /* store number of bytes written from access code */
int n_read =0;
int i=0;
int baud=0;
int bytes_written=0;
/* hold the file descriptor */ 
int fd = 0;  
access_code[0]=0x01; /*fill access code with correct hex data */
access_code[1]=0x00;
access_code[2]=0x00;
access_code[3]=0x00;
access_code[4]=0x08;
access_code[5]=0x02;
access_code[6]=0x03;
re_len = bytes;
memset(re, 0, sizeof(char)*bytes);
//nanopause initialization data
tim.tv_sec = 0;
tim.tv_nsec = 95000000;
/* open the device for writing and reading later. */ 
fd = open( "/tyCo/0", O_RDWR, 0);
//fd = open("TEST.txt", O_RDWR, 0);
//baud = ioctl(fd, FIOBAUDRATE, 19200); /*note test length maybe 576000 b/c terminal*/

for (i=0;i<7;i++){
    n_access = n_access+write( fd, &access_code[i], 1); /* write */ 
}
logfile=fopen ("LOGFILE.txt","a"); /* open log file*/
outputfile=fopen ("SENSORDATA.txt","a"); /* open output file*/
if(fd<0)  /* check for open error */
    fprintf(logfile,"%s","\nerror opening file\n");
fprintf(logfile,"%s" "%d" "%c","number of access code bytes written: ",n_access,'\n'); /* display bytes written*/
//step 1 call completed now pause with nano pause
if(nanosleep(&tim,&tim2)<0){
    fprintf(logfile,"%s","Nano sleep system call failed \n");
}
//step 2 complete now read with read code
n_read = read( fd, re, re_len); /* read */
if(n_read<0)
    fprintf(logfile,"%s","error reading serial data from sensor\n");
bytes_written=fprintf(outputfile,"%s",re);
fprintf(logfile,"%s" "%d" "%c","call and response executed number of bytes written: ",bytes_written,'\n');

//baud = ioctl(fd, FIOBAUDRATE, 57600);
close( fd ); /* close */ 
fclose(logfile);
fclose(outputfile);

Answer 1

它将写出“001 \0 \0 \0 \b 002 003”到 /tyCo/0，这是预期的。为什么需要一次写一个字节？

确保 TEST.txt 文件在写入前 7 个字节后没有任何内容，因为您只写入了 7 个字节。您还可以删除 TEST.txt 文件，触摸该文件使其存在，然后它将只有您写入的 7 个字节。

使用 VxWorks C 将二进制数据发送到串口

Sending Binary Data to serial port using VxWorks C

c

serial-port

vxworks